Part Number: ATmega, Maunfacturer: Atmel, Part Family: AT, File type: PDF, Document: Datasheet – semiconductor. Atmel ATMEGAMI SL Explore Integrated Circuits (ICs) on Octopart: the fastest source for datasheets, pricing, specs and availability. The ATmega is a low-power CMOS 8-bit microcontroller based on the AVR Revision F and onwards are now covered in ATmega datasheet.
|Published (Last):||28 September 2009|
|PDF File Size:||17.18 Mb|
|ePub File Size:||6.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
In other projects Wikimedia Commons. Program instructions are stored in non-volatile flash memory. In Power-save mode, the asyn. Additionally, some atmega196 differences affect code generation.
Atmel has application notes and code pertaining to many bus interfaces. Raven peripherals resemble the Butterfly: The AVR instruction set is more orthogonal than those of most eight-bit microcontrollers, in particular satasheet clones and PIC microcontrollers with which AVR competes today.
The AVR offers several options for debugging, mostly involving on-chip debugging while the chip is in the target system. Retrieved 14 Jun The Power- down mode saves the register contents but freezes the Oscillator, disabling all other chip functions until the next interrupt or hardware reset.
LEDs visible through the translucent case indicate the state of target power. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers.
(PDF) ATMEGA169 Datasheet download
The mostly regular instruction set makes programming it using C or even Ada compilers fairly straightforward. Archived from the original on 15 February Archived from the original on Most instructions take just one or two clock cycles, making AVRs relatively fast among eight-bit microcontrollers. The size of the program memory is usually indicated in the naming of the device itself e. The signal routing board sits between the base board and the target board, and routes the signals to the proper pin on the device board.
The AVR processors were designed with the efficient execution of compiled C code in mind and have several built-in pointers for the task. Conversely, the indirect load instruction’s LD bit address space is expanded to also include non-volatile memory such as Flash and configuration bits; therefore, the Load Program Memory LPM instruction is unnecessary and omitted.
This means the next machine instruction is fetched as the current one is executing. A volt signal, however, is something the AVR should only see during programming and never during normal operation.
The radios are driven with ATmegap processors, which are supported by a custom segmented LCD display driven by an ATmegap processor. The code can re-program datashset any interface available, or it could read an encrypted binary through an Ethernet adapter like PXE. Note that erase and write can be performed separately in many cases, byte-by-byte, which may also help prolong life when amtega169 only need to be set to all 1s erase or selectively cleared to 0s write.
Retrieved 7 November They are especially common in hobbyist and educational embedded applications, popularized by their inclusion in many of the Arduino line of open hardware development boards. The reset line has an internal pull-up resistor, but if the environment is noisy it can be insufficient and reset can therefore occur sporadically.
Among the first of the AVR line was the AT90S, which in a pin DIP package has the same pinout as an microcontroller, including the external multiplexed address and data bus. There are many means to load program code into an AVR chip.
High-voltage parallel programming HVPP is considered the “final resort” and may be the only way to correct bad fuse settings on an AVR chip. The actual Atmdga169 is located after these ranges, starting at All recent Tiny, Mega, and Xmega, but not 90S AVRs feature an on-chip oscillator, removing the need for external clocks or resonator circuitry.
The AVR Butterfly comes preloaded with software to demonstrate the capabilities of the microcontroller. Although the MCUs are 8-bit, each instruction takes one or two bit words. Attmega169 boards can ddatasheet used with its language and IDEor with more conventional programming environments Cassembleretc. For detailed info, see Atmel AVR instruction set. LogicGreen Technologies, a clone of the ATmega The debugWire interface enables debugging using only one pin the Reset pinallowing debugging of applications running on low pin-count microcontrollers.