FUTABA 12Z MANUAL PDF

Instruction manual • Read online or download PDF • Futaba 12Z User Manual. Futaba 12Z User Manual • Motor • Futaba Accessories communication. Read online or download PDF • Page / • Futaba 12Z User Manual • Futaba Accessories communication.

Author: Kigasar Vusar
Country: Haiti
Language: English (Spanish)
Genre: Marketing
Published (Last): 18 February 2013
Pages: 321
PDF File Size: 12.74 Mb
ePub File Size: 5.28 Mb
ISBN: 344-9-36485-186-2
Downloads: 38993
Price: Free* [*Free Regsitration Required]
Uploader: Banos

Setting method tuned for changes in rotor speed accompanying conditions.

Page Setting method enter a point and push the enter button. For PCM mode, you can set eight linear channels and one digital channel. Up, down, left, and right movements are possible.

The Model Select function of the Linkage Menu is used to add models and to select models which are already set. For types, all futbaa will be lost. We will no longer be accepting new service requests. Curve setting operation This section describes the setting procedure of curves which are used with the AFR function and each Curve type selection Curve type selection 1.

When you select model and wing swash types. Normally, it is used with the high side and low side trim function. To add new models or to call a model already set, mankal the Model Select function of the Linkage Menu. Use only the Futaba lithium ion transmitter cutaba included with this set for, or other chargers approved by Futaba to charge the Li-Ion batteries in the 1 Z transmitter. Before Use T12Z is operated by 7. Thank you, Horizon Hobby. Page 43 Receiver and servo connection Connect the receiver and servos in accordance with the connection diagram shown below.

It is used when rudder is applied during roll maneuvers, knife edge, etc. Page 72 which can be switched by switch, etc. Danger Do not connect any other chargers except CR to this charging connector. Page 74 be used for each condition. Winglets are used 21z improve the efficiency of aircraft lowering the fuatba drag caused by wingtip vortices.

  JEAN HYPPOLITE GENESIS AND STRUCTURE PDF

Page 77 fuel mixture control carburetor. Pulse width control, 1. Updating procedure seconds, updating starts. When to PPM mode.

Ailevator is where each elevator in a standard conventional or v-tail moves independently, like ailerons on a wing. It will prevent the engine from racing dangerously when adjusting the Idle-Up settings.

Terms of Use Privacy Policy. Servo connection by model type The T12Z transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu.

The preset elevators and flaps camber flap, brake flap offset amount can be activated by a switch. Page 33 This function registers the T12Z user name. Page 44 Servo connection by model type The T12Z transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu.

Motor – Futaba 12Z User Manual

When transmitting the head. Safety precautions when you install receiver and servos Warning Wood screw 2.

This function is dedicated mixing used in needle adjustment of an engine that uses a fuel mixture control carburetor. Page 89 Setting method turn the data input dial to the left and push the enter The rate and curve of each servo can be set by calling each screen.

Futaba® – Contact Us

The point is created. Page 5 Prior approval of the appropriate government authorities may be required. The T12Z is designed so that the airplane and glider including EP glider model types can handle Page 75 For a description of the setting method, see the description at the back of this manual.

  EUROTHERM 2204 PDF

After the set mode is changed from group mode [GROUP] to single mode [SINGL] at the control selection screen, only that condition setting is changed by control change; setting of other conditions remains the same. Setting of these 2 positions can be selected by switch.

Always read [Precautions when mounting the receiver and servos] of [Before using]. If you later change model commands that apply to helicopters only.

Function, Functions of linkage menu, Function change | Futaba 12Z User Manual | Page 55 /

If the battery fully discharges during During writing, the bar graph moves to the right. The screen depends on the model type. It is used Fine tuning to correct undesirable tendencies when rudder is applied in roll maneuvers, knife edge, etc. When the aileron stick is manipulated, the ailerons and camber flaps perform aileron operation simultaneously and the operation characteristic of the roll axis is improved.

However, when using the 3 smooth curve can be created by selecting the curve type relative to movement of the throttle stick. Use the cursor lever to move the cursor reverse-display to the [POINT] item and turn the data input dial to the left or right and select the point whose rate you want